All of these capabilities were your responsibility to pay for if you set up a network on Zyxel and chose a premium access point. For these circumstances, Zyxel has made available a compact version of the flagship, the WAX630S model without Bluetooth connectivity, with a 2.5-gigabit PoE port, 160 MHz channel width, and 6 spatial streams, offering a total speed of 2.95 Gbit/s. Naturally, management can be accessed via the Nebula Control Center cloud service as well as the direct Web interface. also you can check our article on Zyxel WAX630S review.


From the outside, the WAX630S and the far less expensive NWA90AX(opens in new tab) look nearly identical. The style continuity is rather misleading, though, as this is a larger piece of equipment than the NWA90AX, which is just 14 cm square and 3.75 cm thick. The WAX630S weighs a substantial 530g more than its smaller sibling due to the additional space inside the case. Zyxel also supplies a strong mounting plate that clicks into slots on the underside of the router because having more than half a kilogram of wifi router fall on one’s head would be uncomfortable. The WAX630S can be mounted on the ceiling or the wall equally well thanks to the mounting’s ability to offer support in both vertical and horizontal deployments. Although the antenna can operate in either position, many MESH access point designs are only ceiling-mounted, giving customers with difficult installations some much-needed options.

Zyxel WAX630S review: Internal Hardware

Although we haven’t discovered any seals that could break the warranty, we would still consider that it might if you were to go ahead with the teardown process. In any case, We removed the screws from the bottom of the AP in order to inspect what’s inside the Zyxel WAX630S and to better comprehend the differences between it and the WAX650S. The top portion may then be removed, and just like the WAX650S, a metallic component is fastened to the plastic cover. The metallic casing is intended to dissipate heat from the components in order to keep the gadget from getting too hot to the touch. The plastic stops this from happening. Following that, we were able to distinguish the main parts, including the quad-core Qualcomm IPQ8071A SoC, which is significantly slower than the IPQ8072A of the WAX650S, which was clocked at 2GHz. Then there is the 1GB of DDR4 from Samsung, which we presume is there to balance the less powerful SoC. There is also 8MB of Winbond flash memory, but don’t worry, there is 256MB of MXIC flash memory on the other side of the PCB. In addition, we were able to recognize the Qualcomm QCA8081 Ethernet PHY chip for the 2.5GbE port and the Atheros AR8033-AL1A Ethernet PHY for the LAN port. In terms of WiFi, the Qualcomm QCN5054 44:4 802.11ax SoC and 4x SKY11 85755 highly integrated front-end models for the 5GHz band are both used by the Zyxel WAX650S. Additionally, it includes a 2X Skyworks 85340 6953811 front-end module and Qualcomm QCN5024 802.11b/g/n/ax 22:2 chipset for the 2.4GHz band.


A pair of Ethernet connectors are also available on each unit. The primary one supports 2.5GbE and is compatible with both PoE+ and PoE++ power standards; however, if using a single cable, we strongly advise using PoE++ as the WAX630’s peak performance will otherwise be reduced by 50%. Regular Gigabit rates are supported on the second port, which can be used to connect wired devices or aggregated with the 2.5GbE port when connected to the switch. you can read our article on Zyxel WAX630S review.

Zyxel WAX630S review: Features

The Zyxel WAX630S’s smart antenna technology is one of its standout characteristics. It appears to function similarly to beamforming but does not require the client to exert any effort, hence no specialized compatible hardware is required. In order to ensure that each client device receives the best signal possible, the smart antenna first scans the environment for connected clients and to gain a thorough understanding of the types of interference that may be present. Subsequently, for each client device, it then builds a unique pattern. 700 different combinations are conceivable, and according to Zyxel, each client’s pattern is adjusted extremely quickly. It’s also true that I had no problems with the WAX650S, but the WAX630S has somewhat different internal hardware. We can’t vouch for a larger site, but the few client devices that we can connect to the access point appeared to have no problems (particularly when utilizing NCC). Along with the smart antenna, WiFi 6 has capabilities like OFDMA, which supports both upstream and downstream traffic.


It is quite difficult to test an access point like the WX630S. The device is a moving target for anyone seeking to assess it since it adjusts in real-time to the signals it senses around it and the constantly shifting wireless landscape. Since this unit is more concerned with the quality of the service than the actual maximum speed that any one client may attain, the connection speed of a single customer isn’t the most important factor. What we can tell is that client rates of about 500 mbps on 5 GHz are possible in the same room, and about half that in the next-door room. The 2.4GHz portion of this design seems reliable, and if put internally on an exterior wall, the range at which a connection is still viable should easily extend outside the building. Zyxel graciously provided documentation on how this device’s “smart antenna” performs when mounted on a wall or ceiling and how it differs from the more expensive WAX650S variant. There isn’t much of a performance difference between the two orientations with the WAX630S. The WAX650S has a marginally better signal performance for wall installation and a weaker signal performance for ceiling mounting. Our overall evaluation of this device’s performance is that it is respectable but not outstanding. also you will learn our article on Zyxel WAX630S review. This technology has undergone extensive development to withstand the plethora of invasive signals that a typical city installation provides. However, with so many factors at play, the only way to know if those processes function in that particular scenario is through installation on your premises. There are no assurances with wireless networking, despite the fact that Zyxel developed the WAX630S to give it the greatest opportunity.

Zyxel WAX630S review: Price

The WAX630S has an MSRP of $379.99 through authorised US resellers and is available in the UK for £448.50. If you’re looking for hardware with comparable specifications, the EnGenius ECW230 costs about £435, which is less than the Zyxel by a few pounds. It is important to note that the Zyxel design only has twin channels on 2.4GHz, but the EnGenius ECW230 offers four channels on both 2.4GHz and 5GHz. The WAX650S, a Zyxel design that costs a stunning £744.48 (almost $800 for US consumers) and is the ECW230’s equal, is the same price as the ECW230.


Generally speaking, 2.5-Gigabit Wi-Fi 6 network equipment is becoming available for business use, and it’s especially nice that even in this market segment you can get some interesting technologies, like cloud management, an antenna unit with a variable directional pattern, easy orchestration of wireless networks across the organization, and corporate protection. networks that come from within. There are, of course, certain drawbacks, such as the Zyxel XGS1250-12 network switch’s lack of Nebula compatibility and inability to completely integrate into a single Zyxel ecosystem with control from a single window.

Zyxel WAX630S review  our top pick - 26Zyxel WAX630S review  our top pick - 49Zyxel WAX630S review  our top pick - 16Zyxel WAX630S review  our top pick - 55Zyxel WAX630S review  our top pick - 15Zyxel WAX630S review  our top pick - 57Zyxel WAX630S review  our top pick - 78